Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
What're your thoughts on How to Install a Bathtub?
Mounting a bath tub isn't exactly rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can move quickly; if you need to open up a wall to get rid of the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. Make certain you have actually certified on your own for the job and also are comfortable trying it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to take into consideration employing one before you start. Chances are you may require a professional plumber to make tube connections.
This short article will certainly aid you install a brand-new bathtub in your washroom if you have already acquired a new bathtub as well as do not need to transform the arrangement of your previous water system pipelines.
Your tools and also material list should make up the following:
Planning for the Installment
To start with, the sustaining framework provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to avoid stress on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome because of the restricted accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Activate the water supply as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill up the tub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bathtub needs to wait till the bath tub has actually been utilized at least once as this will resolve it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous type ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, bring about issues with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealer can crack fairly very early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I recently found that piece on A Step-by-Step Guide to Installing a Bathtub while looking around the web. Enjoyed our post? Please share it. Let other people check it out. Bless you for your time. Please pay a visit to our blog back soon.
Visit Website
Report this page